...
| Code Block | ||||
|---|---|---|---|---|
| ||||
tosca.datatypes.nfv.ServiceAvailability:
derived_from: tosca.datatypes.Root
description: service availability
properties:
level:
type: string
description: service availability levels
required: true
constraints:
- valid_values: [ level1, level2, level3 ] |
| Code Block | ||||
|---|---|---|---|---|
| ||||
tosca.datatypes.nfv.L2AddressData:
derived_from: tosca.datatypes.Root
description: Describes the information on the MAC addresses to be assigned to a connection point.
properties:
mac_address_assignment:
type: boolean
description: Specifies if the address assignment is the responsibility of management and orchestration function or not. If it is set to True, it is the management and orchestration function responsibility
required: true |
| Code Block | ||||
|---|---|---|---|---|
| ||||
tosca.datatypes.nfv.L3AddressData:
derived_from: tosca.datatypes.Root
description: Provides information about Layer 3 level addressing scheme and parameters applicable to a CP
properties:
ip_address_assignment:
type: boolean
description: Specifies if the address assignment is the responsibility of management and orchestration function or not. If it is set to True, it is the management and orchestration function responsibility
required: true
floating_ip_activated:
type: boolean
description: Specifies if the floating IP scheme is activated on the Connection Point or not
required: true
ip_address_type:
type: string
description: Defines address type. The address type should be aligned with the address type supported by the layer_protocols properties of the parent VnfExtCp
required: false
constraints:
- valid_values: [ ipv4, ipv6 ]
number_of_ip_address:
type: integer
description: Minimum number of IP addresses to be assigned
required: false
constraints:
- greater_than: 0 |
| Code Block | ||||
|---|---|---|---|---|
| ||||
tosca.datatypes.nfv.AddressData:
derived_from: tosca.datatypes.Root
description: Describes information about the addressing scheme and parameters applicable to a CP
properties:
address_type:
type: string
description: Describes the type of the address to be assigned to a connection point. The content type shall be aligned with the address type supported by the layerProtocol property of the connection point
required: true
constraints:
- valid_values: [ mac_address, ip_address ]
l2_address_data:
type: tosca.datatypes.nfv.L2AddressData
description: Provides the information on the MAC addresses to be assigned to a connection point.
required: false
l3_address_data:
type: tosca.datatypes.nfv.L3AddressData
description: Provides the information on the IP addresses to be assigned to a connection point
required: false |
| Code Block | ||||
|---|---|---|---|---|
| ||||
tosca.datatypes.nfv.ConnectivityType:
derived_from: tosca.datatypes.Root
description: describes additional connectivity information of a virtualLink
properties:
layer_protocols:
type: list
description: Identifies the protocol a virtualLink gives access to (ethernet, mpls, odu2, ipv4, ipv6, pseudo-wire).The top layer protocol of the virtualLink protocol stack shall always be provided. The lower layer protocols may be included when there are specific requirements on these layers.
required: true
entry_schema:
type: string
constraints:
- valid_values: [ ethernet, mpls, odu2, ipv4, ipv6, pseudo-wire ]
flow_pattern:
type: string
description: Identifies the flow pattern of the connectivity
required: false
constraints:
- valid_values: [ line, tree, mesh ] |
| Code Block | ||||
|---|---|---|---|---|
| ||||
tosca.datatypes.nfv.NsVlProfile:
derived_from: tosca.datatypes.Root
description: Describes additional instantiation data for a given NsVirtualLink used in a specific NS deployment flavour.
properties:
max_bitrate_requirements:
type: tosca.datatypes.nfv.LinkBitrateRequirements
description: Specifies the maximum bitrate requirements for a VL instantiated according to this profile.
required: true
min_bitrate_requirements:
type: tosca.datatypes.nfv.LinkBitrateRequirements
description: Specifies the minimum bitrate requirements for a VL instantiated according to this profile.
required: true
qos:
type: tosca.datatypes.nfv.NsVirtualLinkQos
description: Specifies the QoS requirements of a VL instantiated according to this profile.
required: false
service_availability:
type: tosca.datatypes.nfv.ServiceAvailability
description: Network service virtual link service availability levels, as described in ETSI GS NFV-REL 001
required: false |
| Code Block | ||||
|---|---|---|---|---|
| ||||
tosca.datatypes.nfv.VirtualLinkProtocolData:
derived_from: tosca.datatypes.Root
description: describes one protocol layer and associated protocol data for a given virtual link used in a specific VNF deployment flavour
properties:
associated_layer_protocol:
type: string
description: Identifies one of the protocols a virtualLink gives access to (ethernet, mpls, odu2, ipv4, ipv6, pseudo-wire) as specified by the connectivity_type property.
required: true
constraints:
- valid_values: [ ethernet, mpls, odu2, ipv4, ipv6, pseudo-wire ]
l2_protocol_data:
type: tosca.datatypes.nfv.L2ProtocolData
description: Specifies the L2 protocol data for a virtual link. Shall be present when the associatedLayerProtocol attribute indicates a L2 protocol and shall be absent otherwise.
required: false
l3_protocol_data:
type: tosca.datatypes.nfv.L3ProtocolData
description: Specifies the L3 protocol data for this virtual link. Shall be present when the associatedLayerProtocol attribute indicates a L3 protocol and shall be absent otherwise.
required: false |
| Code Block | ||||
|---|---|---|---|---|
| ||||
tosca.datatypes.nfv.L2ProtocolData:
derived_from: tosca.datatypes.Root
description: describes L2 protocol data for a given virtual link used in a specific VNF deployment flavour.
properties:
name:
type: string
description: Identifies the network name associated with this L2 protocol.
required: false
network_type:
type: string
description: Specifies the network type for this L2 protocol.The value may be overridden at run-time.
required: false
constraints:
- valid_values: [ flat, vlan, vxlan, gre ]
vlan_transparent:
type: boolean
description: Specifies whether to support VLAN transparency for this L2 protocol or not.
required: false
default: false
mtu:
type: integer
description: Specifies the maximum transmission unit (MTU) value for this L2 protocol.
required: false
constraints:
- greater_than: 0 |
| Code Block | ||||
|---|---|---|---|---|
| ||||
tosca.datatypes.nfv.L3ProtocolData:
derived_from: tosca.datatypes.Root
description: describes L3 protocol data for a given virtual link used in a specific VNF deployment flavour.
properties:
name:
type: string
description: Identifies the network name associated with this L3 protocol.
required: false
ip_version:
type: string
description: Specifies IP version of this L3 protocol.The value of the ip_version property shall be consistent with the value of the layer_protocol in the connectivity_type property of the virtual link node.
required: true
constraints:
- valid_values: [ ipv4, ipv6 ]
cidr:
type: string
description: Specifies the CIDR (Classless Inter-Domain Routing) of this L3 protocol. The value may be overridden at run-time.
required: true
ip_allocation_pools:
type: list
description: Specifies the allocation pools with start and end IP addresses for this L3 protocol. The value may be overridden at run-time.
required: false
entry_schema:
type: tosca.datatypes.nfv.IpAllocationPool
gateway_ip:
type: string
description: Specifies the gateway IP address for this L3 protocol. The value may be overridden at run-time.
required: false
dhcp_enabled:
type: boolean
description: Indicates whether DHCP (Dynamic Host Configuration Protocol) is enabled or disabled for this L3 protocol. The value may be overridden at run-time.
required: false
ipv6_address_mode:
type: string
description: Specifies IPv6 address mode. May be present when the value of the ipVersion attribute is "ipv6" and shall be absent otherwise. The value may be overridden at run-time.
required: false
constraints:
- valid_values: [ slaac, dhcpv6-stateful, dhcpv6-stateless ] |
| Code Block | ||||
|---|---|---|---|---|
| ||||
tosca.datatypes.nfv.IpAllocationPool:
derived_from: tosca.datatypes.Root
description: Specifies a range of IP addresses
properties:
start_ip_address:
type: string
description: The IP address to be used as the first one in a pool of addresses derived from the cidr block full IP range
required: true
end_ip_address:
type: string
description: The IP address to be used as the last one in a pool of addresses derived from the cidr block full IP range
required: true |
| Code Block | ||||
|---|---|---|---|---|
| ||||
tosca.datatypes.nfv.LinkBitrateRequirements:
derived_from: tosca.datatypes.Root
description: describes the requirements in terms of bitrate for a virtual link
properties:
root:
type: integer # in bits per second
description: Specifies the throughput requirement in bits per second of the link (e.g. bitrate of E-Line, root bitrate of E-Tree, aggregate capacity of E-LAN).
required: true
constraints:
- greater_or_equal: 0
leaf:
type: integer # in bits per second
description: Specifies the throughput requirement in bits per second of leaf connections to the link when applicable to the connectivity type (e.g. for E-Tree and E LAN branches).
required: false
constraints:
- greater_or_equal: 0 |
| Code Block | ||||
|---|---|---|---|---|
| ||||
tosca.datatypes.nfv.NsVirtualLinkQos:
derived_from: tosca.datatypes.nfv.Qos
description: describes QoS data for a given VL used in a VNF deployment flavour
properties:
priority:
type: integer
description: Specifies the priority level in case of congestion on the underlying physical links
required: false |
| Code Block | ||||
|---|---|---|---|---|
| ||||
tosca.datatypes.nfv.CpProtocolData:
derived_from: tosca.datatypes.Root
description: Describes and associates the protocol layer that a CP uses together with other protocol and connection point information
properties:
associated_layer_protocol:
type: string
required: true
description: One of the values of the property layer_protocols of the CP
constraints:
- valid_values: [ ethernet, mpls, odu2, ipv4, ipv6, pseudo-wire ]
address_data:
type: list
description: Provides information on the addresses to be assigned to the CP
entry_schema:
type: tosca.datatypes.nfv.AddressData |
| Code Block | ||||
|---|---|---|---|---|
| ||||
tosca.datatypes.nfv.VnfProfile:
derived_from: tosca.datatypes.Root
description: describes a profile for instantiating VNFs of a particular NS DF according to a specific VNFD and VNF DF.
properties:
instantiation_level:
type: string
description: Identifier of the instantiation level of the VNF DF to be used for instantiation. If not present, the default instantiation level as declared in the VNFD shall be used.
required: false
min_number_of_instances:
type: integer
description: Minimum number of instances of the VNF based on this VNFD that is permitted to exist for this VnfProfile.
required: true
constraints:
- greater_or_equal: 0
max_number_of_instances:
type: integer
description: Maximum number of instances of the VNF based on this VNFD that is permitted to exist for this VnfProfile.
required: true
constraints:
- greater_or_equal: 0 |
| Code Block | ||||
|---|---|---|---|---|
| ||||
tosca.datatypes.nfv.Qos:
derived_from: tosca.datatypes.Root
description: describes QoS data for a given VL used in a VNF deployment flavour
properties:
latency:
type: scalar-unit.time #Number
description: Specifies the maximum latency
required: true
constraints:
- greater_than: 0 s
packet_delay_variation:
type: scalar-unit.time #Number
description: Specifies the maximum jitter
required: true
constraints:
- greater_or_equal: 0 s
packet_loss_ratio:
type: float
description: Specifies the maximum packet loss ratio
required: false
constraints:
- in_range: [ 0.0, 1.0 ] |