...

...

Goal

A planned list of 5G nodes are on-boarded into ONAP, and ONAP configures the nodes to the level that they are ready to handle traffic. ONAP begins to actively monitor and manage the nodes.

...

• The 5G nodes consist of both PNFs (DU) and VNFs (CU). A single CU may consist of several VNFs.
• Scope is limited to one PLMN without slicing.
• A single vendor delivers RAN equipment and software.
• A single service provider:
• Owns or leases data center equipment, cell sites, physical transport, and any new equipment installed on these sites
• Owns and operates the resulting RAN
• Is the single user of the entire ONAP based management system
Use
• • VNF/PNF provider is not visible as actor in this use case and self-service for VNF/PNF onboarding is not supported.
• Network status including KPIs can be monitored in Portal (dashboard), but exporting data via APIs to external monitoring applications is out of scope.
• This use case covers only initial deployment of nodes. Thus, change management such as software upgrade is out of scope.

...

The 5G RAN is providing RAN service for the user equipment according to expectations:

• All planned services are on-lineonline, providing FCAPS data through the relevant channels
• RAN NOC personnel have full access to the FCAPS data and ONAP automation framework
• Dashboard or other NOC tools configured to display displays relevant RAN data
• Calculation and monitoring of key performance indicators is activated, used to verify the capacity requirements
• A first automation use
-
• case reacting on an incident or state change
have
• has been implemented

Steps

(Oskar M.) More sequences diagrams to added to steps below. Diagram in step 3 needs some more details.

Step 1: Service

...

design

...

• Onboard SW packages, descriptors and any other artefacts provided by the RAN vendorOnboard any planning data that is common across all nodes
• Design RAN-level templates, recipes and workflows covering common network elements, transport network, data collection and analytics, policies and corrective actions
• Design node-level templates, recipes and workflows covering network elements (PNFs and VNFs), transport network, placement or QoS constraints, data collection and analytics, policies and corrective actions

...

• Distribute the completed design as well as vendor-provided artefacts to the various run-time components.

(Oskar M.) General ONAP question: Are WAN resource requirements embedded in service template parsed by SO, or do they use separate descriptors that shall be distributed to SDNC?

Gliffy
name RAN_deploy_step_1

Step 2: Verify design

• Verify templates and recipes from step 1, using dedicated test environment or limited trial following steps below. If necessary, make adjustments according to step 1.

Step 3: Deploy shared services

...

This step refers to deployment of any shared RAN services and functions defined by templates, recipes and workflows in step 1. Note that some of the functions below may be partially inactive until nodes are added in step 4.

• On receiving service instantiation request via Portal or external API, SO and controllers will decompose the request, and allocate and connect the various resources.
• DCAE will start fault, performance, and log data collection as described during design time.
• DCAE will perform data analytics as configured in recipes, to monitor the environment and publish detect anomalous conditions. Corrective/remedial action for network impairments and for violations of service levels as described by defined policies are initiated using the SO and/or controllersOutput from analytics is forwarded to Policy and dashboard.

(Oskar M.) General ONAP question: The diagram below is modeled based on some other ONAP use cases. Why is there a service instantation request towards SO, but no corresponding requests towards DCAE or Policy to instantiate/activate analytics blueprints or policy rules for this particular service instance?

Gliffy
name RAN_deploy_step_2

.

Step 4: Add nodes

...

This step refers to deployment of services and functions defined by templates, recipes and workflows in step 1 for a new 5G node.

• A sub-flow includes the onboarding process for related PNFs.
• In this step node-specific data from planning is also inserted.
• On receiving request, SO and controllers will decompose the request, and allocate and connect the various resources.
• DCAE will start fault, performance, and log data collection as described during design time.
• DCAE will perform data analytics as configured in recipes, to monitor the environment and publish detect anomalous conditions. Output from analytics is forwarded to Policy and dashboard.

Step 5: Verify operation

• Verify that service is provided and can be monitored through dashboard using basic observability data and calculated KPIs.

Step 6: React to incident

• Corrective/remedial action for network impairments and or for violations of service levels as described by defined policies are initiated using the SO and/or controllersThis step is repeated for each added node. Bulk deployment should be possible to handle a larger number of nodes in an efficient way.

Step 5: Final verification (run-time including dashboard)

• Verify that service is provided and can be monitored through dashboards and northbound APIs using basic observability data and calculated KPIs
  • For verification purposes this may require fault injection.
• Verify that policy definitions and their corrective actions are active and has have intended effect.