Page Comparison

...

1. Pull the custom honeycomb docker image using the command

   Code Block
   language bash title Docker pull command
   docker pull docker.io/tragait/gnbsim:v1

   
   

2. Clone/download https://github.com/onap-oof-pci-poc/ran-sim

3. Update ransim and honeycom IP address at '<YOUR_DIRECTORY>/ran-sim/hcsim-content/gnbsim/hc/config/gnbsim.json'
   Make sure the following are updated to.
   To get the ransimIp and hcIp do the following:

   Code Block
   language bash title Inspect ransim ip
   docker inspect -f '{{range.NetworkSettings.Networks}}{{.IPAddress}}{{end}}' <ransim_CONTAINER_ID>

   
   

   • "ransimIp": <ransimIP>
   • "ransimPort": 8081
   • "hcIp": <ransimIP>
   • "hcPort": 2831
4. Update the image name in the '<YOUR_DIRECTORY>/ran-sim/hcsim-content/gnbsim/hc/docker-compose.yml' to:
   • image: tragait/gnbsim:v1
     

5. Run the below command from '<YOUR_DIRECTORY>/ran-sim/hcsim-content/gnbsim/hc' directory
   

   Code Block
   language bash title Docker compose up command
   docker-compose up -d

   While running the docker-compose up -d command, these servers will be mounted in SDNC 
   In case these servers are not mounted in SDNC, you can use the following curl command to mount the HC sim.
   To get the ip of the hc sim do the following:
   
   

   Code Block
   language bash title Inspect hc ip
   docker inspect -f '{{range.NetworkSettings.Networks}}{{.IPAddress}}{{end}}' <hc_CONTAINER_ID>

   Make sure to modify the below curl command, replace HC_SIM_IP with the ip retrieved from previous command.
   Note. If using WSL 2  then the HC_SIM_IP in the below curl command can be replaced with ip address got from doing : 

   wsl hostname -I in the windows powershell. 

   Code Block
   language bash title HC sim mount command
   curl -i -X PUT http://localhost:8282/restconf/config/network-topology:network-topology/topology/topology-netconf/node/hc -k -H 'Accept: application/xml' -H 'Content-Type: text/xml' --user "admin":"Kp8bJ4SXszM0WXlhak3eHlcse2gAw84vaoGGmJvUy2U" -d '<node xmlns="urn:TBD:params:xml:ns:yang:network-topology"> <node-id>hc</node-id> <host xmlns="urn:opendaylight:netconf-node-topology">HC_SIM_IP</host> <port xmlns="urn:opendaylight:netconf-node-topology">2831</port> <username xmlns="urn:opendaylight:netconf-node-topology">admin</username> <password xmlns="urn:opendaylight:netconf-node-topology">admin</password> <tcp-only xmlns="urn:opendaylight:netconf-node-topology">false</tcp-only> <!-- non-mandatory fields with default values, you can safely remove these if you do not wish to override any of these values--> <reconnect-on-changed-schema xmlns="urn:opendaylight:netconf-node-topology">false</reconnect-on-changed-schema> <connection-timeout-millis xmlns="urn:opendaylight:netconf-node-topology">20000</connection-timeout-millis> <max-connection-attempts xmlns="urn:opendaylight:netconf-node-topology">0</max-connection-attempts> <between-attempts-timeout-millis xmlns="urn:opendaylight:netconf-node-topology">2000</between-attempts-timeout-millis> <sleep-factor xmlns="urn:opendaylight:netconf-node-topology">1.5</sleep-factor> <!-- keepalive-delay set to 0 turns off keepalives--> <keepalive-delay xmlns="urn:opendaylight:netconf-node-topology">120</keepalive-delay></node>'

   
   

6. Check using 'docker container ls' that the honeycomb simulator is up and running.
   

Once the above steps have been completed, check if the honeycomb simulator has been mounted in SDNC by going to the following link and clicking on the Mounted Resources section:
 http://localhost:8282/apidoc/explorer/index.html
Note. If using WSL 2 then the localhost can be replaced with ip address got from doing :
wsl hostname -I in the windows powershell. 

• Credentials  : - admin / Kp8bJ4SXszM0WXlhak3eHlcse2gAw84vaoGGmJvUy2U

...